Welcome to the official website of ARK Fluid Technology Co.,Ltd!

Add to Favorite| Leave a Message| Contact Us | Website Map|Chinese

ARK Fluid:0086-510-88552288WUXI ARK FLUID SCIENCE TECHNOLOGY CO.,LTD.

E-mail:199601@wxark.cn   199612@wxark.cnMobile:0086-13616187265 Joan0086-15852783915 Sun

Tel:0086-510-88552288

Hot keywords:crossflow cooling towercounter flow cooling towerwater chiller unitsopen circuit cooling towercrossflow cooling tower designclosed circuit cooling towerRound cooling towersquare cooling tower

ARK Cooling tower

Open type cross-flow cooling towers-FKH

Product category: Open Cooling Tower
ShortDesc:Overview
International design working condition of the cooling tower: water inlet temperature t1 = 37; water outlet temperature t2 = 32wet bulb temperature t = 28dry-bulb temperature=31.5atmospheric pressure=9.94X104pa.
Hotline: 0086-510-88552288

Open type cross-flow cooling towers-FKH

Open type cross-flow cooling towers-FKH

I.Overview

International design working condition of the cooling tower: water inlet temperature t1 = 37; water outlet temperature t2 = 32wet bulb temperature t = 28dry-bulb temperature=31.5atmospheric pressure=9.94X104pa.

The standard cooling tower of the company is designed according to the national working condition. We can also provide special design for non-standard working condition to customers.

Due to site limitation or modeling requirement, the company especially design and custom make the cooling tower according required dimensions. Contact us for details.

Base bearing surfaces are in a same horizontal plane and its elevation and each dimension error is less than 5mm.

Base height of the cooling tower h2 should be determined according to the pipe diameter of the water outlet pipe and installation height.

Our company will provide connection balance pipe and balance base plate water level when assembling two or more than two towers.

If users require our company increase the water outlet flange bore diameter, please note it when ordering.

The measuring point for noise at from the Dm point of the cooling tower equivalent diameter.
Dm = Height above ground is 1.5 meters, where L, W is )

Pipe connecting chart is the pipe connecting position dimension of one unit, multiple units assembly is in the same way.

When a different models tower are connected, the base plate water level height (size E) of different model tower must be considered to adjust basic height to maintain the water level balance of all towers.

Pictures and technical parameters in samples are for your reference only. Our company reserves the right to improve constantly, modify product appearance and technical parameters.

 

II. Product selection

 

Product selection

FKH Production selection
Click to zoom in


III. Product structure

The high-quality raw material PVC sheet in use is processed by hot press molding or vacuum molding; the tower is designed in the whole suspension and can resist corrosion and biological erosion; the unique 3D folded hole design is featured with extremely high water collection efficiency and extremely low air resistance and can control drift loss below 0.0005% of circulating water so as to save water energy in maximum and prevent the transmission of legionnaires disease bacteria.

 

Structure details:


The characteristics of opened cooling tower -FKH

New technologyThe whole cooling fin based on advanced technology optimizes design structure and makes reasonable volume.

New materialThe improved fireproof PVC raw material is used as the material of cooling fin and FRP is made of the latest improved material in USA.

New processThe primary molding of adsorption plastic mould is adopted. The split jointing is used for structure, rapid and firm.

New product Cooling performance is 105%, drift rate is not more than 0.001% and the new product is characterized by novel appearance, reasonable structure and equitable price. The combined tower can be assembled according to site conditions.

Equipment structure diagram

Equipment structure diagram

 

Belt (rubber) cast ironFRPBelt cover (FRP) Electric motor (fully-enclosed) FRPAir duct (FRP) Fan shellaluminium alloy : Air blower for wing unit (Hot dip galvanized steel) Ladder (hot-dip galvanized steel) PVCInner connecting pipePVC FRPWater spray basin coverFRPFRPSide plateFRPFRPAccess doorFRPAisleHot dip galvanized steelPPWater distribution sprayerPPPVCSpray packing (flame retardant PVC)
Flange for outlet water (hot-dip galvanized steel) FRPSump basinFRP

 

IV. Technical specification

(1). Cooling system

Cooling System

Packing (Famous Taiwan enterpriseFormosa Plastic Group) The high-quality raw material PVC sheet in use is processed by hot press molding or vacuum molding; the tower is designed in the whole suspension and can resist corrosion and biological erosion; the unique 3D folded hole design is featured with extremely high water collection efficiency and extremely low air resistance and can control drift loss below 0.0005% of circulating water so as to save water energy in maximum and prevent the transmission of legionnaires disease bacteria.


(2). Bulk water system 

Bulk water system

The square tower is set with unique overflow device and shower nozzle so as to make cooling water distributed stably and evenly and meet the requirements of energy saving of the system under different loads (The cooking water flow will vary).
 

(3). Motor for pneumatic system: The motor only for the fully closed air cooling tower is of IP55 and insulation level of Level F, and suitable for 380V/3/50Hz power supply. 

Motor for pneumatic system

Fan blade: The fan blade is made of aluminum alloy and characterized by light weight, high strength, high air flow, low speed in operation, low energy consumption, low noise and long service life. The angle can be adjusted arbitrarily according to the operation load and the rated power is utilized in maximum so as to make the fan in the best operation status.

Fan blade 
 

(4). Transmission deceleration system

Transmission deceleration system 

The standard product is set with the belt reducer, the import waterproof anti-skid belt and import high-precision bearing are adopted, and there is long service life and low noise in operation.

 

(5). Mechanical structure Shell (America famous enterpriseAshland)

Mechanical structure Shell 

  The imported weather-resistant gel coating which resists corrosion and contains uvioresistant stabilizer and is characterized by color uniformity, color fading resistance, anti-aging and surface as smooth as mirror is used. The round tower is designed like a bottle and the square tower is designed with the stripe surface and in round corner so that the surface is free from reflection of light to prevent light pollution.



The structure of tower body

The structure of tower body  

The hot-dip galvanized steel is used. The fastener for tower body is made of #304 stainless steel so as to guarantee corrosion resistance of the whole tower and improve the service life of tower. The tower body can resist the wind load of 150kg/m2, bear the load of Level XII typhoon and resist the seismic intensity of Level VIII.

 

   V. Equipment service commitment

Item

Services

Remarks



Technical support


1. Installation instructions and debugging free of charge.

2. The technical drawings submitted include: outline drawing, foundation drawing, electrical schematic diagram and operation instructions.

3. Training: The free training is provided for 1~2 operators on the site.

 



Quality assurance


1. After the equipment passes final acceptance inspection, the warranty period is 12 months in which the parts and services are provided free of charge and the service is duly and effective.

2. For any failure in warranty period, the warranty period of the new parts after replacement or maintenance will be recalculated from replacement date or maintenance completion date.

3. For any repeated failure in warranty period, the faulty components will enjoy free lifetime guarantee.

 



After-sales service


1. After the equipment failure information is received from the user, it is required to give response within 2 hours and make troubleshooting and deliver the equipment for service within 3 working days.

2. We still provide wide and preferential technical support, accept consultation, supply spare parts for the equipment and adopt the minimum price in charge after warranty period expires.

3. The lifetime service system is implemented.

 

 

 

* Indicated required fieldInquire: Open type cross-flow cooling towers-FKH
* Your Name: Please fill in your First Name
* Last Name: Please fill in your Last Name
Company name: Please fill in your company name
Telephone number:
Mobile phone number: Please fill in your telephone number
* E-mail:
Country:
Address:
* Inquire intention description:
Verification code: Not see?!
Please fill in the quantity and description of Inquire products for uniform stocking.

Hot products

Contact ARK
Wuxi Ark Fluid Science Technology Co., Ltd.

Hotline: 0086-510-88552288

Fax: 0086-510-81152626

E-mail: 199601@wxark.cn

ADD: No.58 Xinfeng Road, Xintai Industrial Zone, Meicun, New Area, Wuxi City,Jiangsu Province